Home > Want To > Want To Install Ethernet In NT System

Want To Install Ethernet In NT System

Poor|Excellent Yes No Document Quality? Setting Up TCP/IP Install your Ethernet adapter following the manufacturer's instructions. You can also purchase several books relating to this topic at your favorite bookstore. For example, if your workstation has a domain name such as example.com, enter it here. his comment is here

Install Wingate and configure it to provide DNS support. Note: You will need to contact your MIS department or your Network Service Provider to learn about the correct configuration settings for your network. You need to assign a WINS server on the Handheld PC as well - it is the same IP address as the Windows 95/NT PC (192.168.1.1 in my example). Use the Add Printer Wizard to install the Hewlett-Packard Network Port and configure the print device.

The WINS Address tab is shown in Figure 3.24. Proceed to How to ActiveSync via Ethernet. Windows CE Ethernet Connectivity FAQ By Chris De Herrera, Copyright 1997-2001 Version 1.73 Revised 2/17/2001 Sections: Introduction, Requirements, Setup Overview, TCP/IP Only, W/Windows NT Server, Full TCP/IP, Minimal TCP/IP, How to Windows NT -based DLC provides applications only with direct access to the data link layer.

If possible, install only the TCP/IP protocol. Second, find the smbpasswd program on the samba server (it is located in /usr/local/samba/bin by default) and use it to add an entry to Samba's encrypted password database. Note: The Handheld PC Pro is configured identical to the Handheld PC. Please click bellow to pass protection, Or you will be automatically redirected to the requested page after 3 seconds.

Please refer to the Configuring your VXI/VME or PXI controllerÂ’s ethernet adapter in Windows NT document if this is not the case. The Workstation service is mandatory. Join over 733,556 other people just like you! http://www.pocketpcfaq.com/wce/20/ethernet.htm You probably noticed that there is a field here for the adaptor; this field must specify the Ethernet adaptor that you're running TCP/IP on so that WINS will provide name service

Optional Components Windows NT Server or Wingate. RFC 1918 defines private IP addresses that you can use without conflicting with previously assigned addresses. Palm-size PC Although the Start -> Control Panel -> Network screen is not formatted for the Palm-size PCs screen, you can still configure it. You can arrange either to bring in a blank CD-R to get a copy of the necessary software or to bring in your computer to have a staff member install the

You also must enter the Identification information as well. http://www1.udel.edu/topics/connect/ethernet/NT/winNTeth-cd.html I am guessing it is not as simple as a win98 or xp system? Click Control Panel and double-click the Network Control Panel. Please see the Network Utilities FAQ for a list of TCP/IP diagnostic programs such as Ping, Trace Route, NSLookup, etc.

If it's not there, you can install it much like TCP/IP. It looks like the following: #resolv.conf domain example.com nameserver 127.0.0.1 nameserver 192.168.236.20 In this example, the first nameserver in the list is 127.0.0.1, which indicates that the Samba server is also This file will then serve the same purpose as the hosts file on the Unix server. For a LAN that's not on the Internet, the list of possible hosts is typically small and well known, and may be kept in a file locally.

Show Ignored Content As Seen On Welcome to Tech Support Guy! Generated Fri, 17 Mar 2017 20:36:11 GMT by s_sr83 (squid/3.5.20) In this case, the workgroup name is SIMPLE. weblink Click here to join today!

Select the TCP/IP protocol; then, click Next> as in the following screen: You do not need to make any changes on the following screen. There are six basic steps: Assign the machine a name. There are three timers used by DLC link communication: •T1--the response timer •T2--the acknowledgment delay timer •Ti--the inactivity timer Each timer is split into two groups--TxTickOne and TxTickTwo, where x is 1, 2, or

If you are in doubt as to whether a DNS server is being used, or what its address might be, look at the file /etc/resolv.conf on your Samba server: any machine

Advertisement chewie1012 Thread Starter Joined: Dec 27, 2001 Messages: 1,062 I am wanting to install a ethernet card in a NT system and am wondering what the steps are. We recommend against this because maintenance of this file on any dynamic network is troublesome, but we will explain it just the same. DLC can also transmit and receive type 1 connectionless frames, such as Unnumbered Information (UI) frames. If you are using the WWW proxy service of Wingate, don't forget to configure your Pocket IE with that address.

The system returned: (22) Invalid argument The remote host or network may be down. For more information, see the warning under the "Accessing the Samba Server" section, earlier in this chapter. Otherwise, provide the address of another WINS server on your network. To change the address of an adapter card 1.Click Start, and then click Run. 2.Type regedit, and click OK. 3.When the Registry Editor starts, select the following key: HKEY_LOCAL_MACHINE \SYSTEM \CurrentControlSet \Services \ibmTOKMC01 4.On the

there are, however, sometimes problems trying to get it to work on whatever network youre trying to get in touch with. Your cache administrator is webmaster. Latest Podcast Subscribe to Podcast Recommended Follow Us You are reading NT4 Installation/Setup of Network-Drivers Share No Comment TECHGENIX TechGenix reaches millions of IT Professionals every month, and has set the Staff Online Now TerryNet Moderator valis Moderator Macboatmaster Trusted Advisor Advertisement Tech Support Guy Home Forums > Internet & Networking > Networking > Home Forums Forums Quick Links Search Forums Recent

These are set in the Control > Panel Network > Properties. there are no other tricks to actually installing it. The DLC protocol driver provided with Windows NT enables the computer to communicate with other computers running the DLC protocol stack (for example, an IBM mainframe) and other network peripherals (for Windows CE does not support a Hosts file in lieu of a DNS server.

I recommend using another Workgroup/Domain Name instead of the default name of Workgroup in order to avoid allowing users to access your data when you are dialed up to the internet. These values control the various timers that DLC uses, whether DIX frames should be used over an Ethernet link, and whether bits in a destination address should be swapped (that is, How to ActiveSync via Ethernet You are all set! Developer Note: Remote debugging is supported with the Embedded Toolkit (ETK) v2.1 or later.

You usually do not want NetBEUI installed because this causes the machine to look for services under two different protocols, only one of which is likely in use.[ 2] [2] A Microsoft does not ship standard TCP/IP diagnostic programs with PC Companions. Now that you've finished setting up the Samba server and its clients, we can starting talking about how Samba works and how to configure it to your liking. 3.1 Setting Up Top of pageCommunicating with SNA Hosts Using DLC One of the major uses of the DLC protocol is connecting personal computers to Systems Network Architecture (SNA) hosts--that is, IBM mainframe or

The first time you click the Network Control Panel, you will be prompted to install networking: Click Yes to install NT Networking.